Search results on bottom layer

Rubik's Revenge Solution - Top Corners (16.0 kb) Relevance : 100.00 % limit to http://helm.lu/, this path : cube/solutions/revenge/topcorners/
...r, rotate the bottom layer until you can position it directly below where it belongs - in the front-bottom-right corner. If you can not find the piece on the bottom layer skip to the THIRD corner and ... ...have these corners completed. Since we are looking for the Orange/Green/White corner, rotate the bottom layer until you can position it directly below where it belongs - in the front-bottom-right cor... ...ner. If you can not find the piece on the bottom layer skip to the FOURTH corner and return to this step a little later. If you did find a match, follow one of the three steps below to move the piece ... ...l have these corners completed. Since we are looking for the Orange/White/Yellow corner, rotate the bottom layer un...
http://helm.lu/cube/solutions/revenge/topcorners/topcorners.htm - last update : 2006-01-03
Rubik's Revenge Solution - Top Bottom Edges (22.9 kb) Relevance : 94.28 % limit to http://helm.lu/, this path : cube/solutions/revenge/topbottomedges/
... TOP/BOTTOM EDGES: RED FACE Let's start by completing the Red Edges. The premise for this step is to find and move all appropriate edges, from the two center rows, up onto the Red Side of the cube. U... ...of the cube. If you run out of pieces on the two center rows: You will most likely find more on the bottom layer. If so, the fifth st... ...ep below will move bottom pieces up into the two center rows so that you can use steps 1 through 4 to properly place the pieces. It is also possible that all the Red Edges are actually on the top but ... ...will move bottom Gray pieces up into the two center rows so that you can use steps 1 through 4 to properly place the pieces. It is also possible that all the Orange Edges are actually on the Orange Fa...
http://helm.lu/cube/solutions/revenge/topbottomedges/topbottomedges.htm - last update : 2006-01-03
Rubik's Cube: Middle Layer (5.8 kb) Relevance : 83.15 % limit to http://helm.lu/, this path : cube/solutions/rubikscube/centeredge/
...Now that you have finished the entire Top Layer of the cube you are ready to start solving the Middle Layer. The Middle Edges When you finish this next step your cube will look like this: Before we s... ...tart, rotate the top layer until the center colors on all 4 sides match the top row. This will in effect lock the two top rows into position. We're getting closer. Your cube should look like this: The... ... scenarios you will face when tackling this middle row. To start, simply look at the 4 edges on the Bottom Layer and find one piece that does not belong on the Bottom Layer. Once... ... you have found one, simply rotate the Bottom Layer until you match one of these two possibilities as shown below, and follow the direction below the appropriate match: The third possibility is that ...
http://helm.lu/cube/solutions/rubikscube/centeredge/centeredge.html - last update : 2006-01-03
Rubik's Revenge Solution - Bottom Corners (12.2 kb) Relevance : 66.67 % limit to http://helm.lu/, this path : cube/solutions/revenge/bottomcorners/
... Next, the Bottom Corners will be completed. This will require you to flip your cube upside down so that the semi-completed Orange side is facing up right, once again. This is a two step process. Fir... ...bottom layer that have Yellow on them. If they are next to each other, simply rotate the bottom until those two yellow corners are on the front side. If they are in their proper positions, you can pro... ...form the following step. If they are already in place, proceed to the next step . Finishing the Bottom Corners At this point, all 4 corners are in place but they probably are not properly rotated yet... .... This next step will require you to flip your cube over again, so that the Orange Side is on the bottom. Fortunately there is only one procedure to remember when orienting the Bottom Corners. Unfortu...
http://helm.lu/cube/solutions/revenge/bottomcorners/bottomcorners.htm - last update : 2006-01-03
Rubik's Pocket Cube: Bottom Corner Position (7.0 kb) Relevance : 66.67 % limit to http://helm.lu/, this path : cube/solutions/pocketcube/bottomplace/
...Now that you have reviewed the Terminology and successfully completed the Top Layer , you are ready to position the bottom corners. At this time you only need to be concerned about making sure the bot... ... will twist each corner in the Last Step to match all of the colors up. Find the two corners on the bottom layer that have green on them. It does not matte... ...h directions the green colors face. If the two green corners are next to each other then rotate the bottom layer until you can match your Pocket Cube to the picture below. NOTE: If... ... need to skip to the diagonal procedure. NOTE: The appearance of the many green stickers on the two bottom corners is only to show that...
http://helm.lu/cube/solutions/pocketcube/bottomplace/bottomplace.html - last update : 2006-01-03
Rubik's Pocket Cube: Top Layer (14.1 kb) Relevance : 44.44 % limit to http://helm.lu/, this path : cube/solutions/pocketcube/top/
...you are ready to start solving the Pocket Cube. You will solve the cube in the following order: Top Bottom Corner Positioning Bottom Completion The ... ...solved piece in the upper left-hand corner, spin the bottom of the Pocket Cube until you find the piece you want the Red/Blue/Yellow corner . Note: It is possible that the corner you are looking for i... ...s not presently on the bottom. If this is the case you will need to jump to The Third Corner and then come back to this corner last. Once you have found the piece you wanted, keep turning the bottom u... ...ntil the piece is in the bottom right-hand corner, directly below where you want to place it. Your Pocket Cube should match one of the three images below. Follow the procedure below the appropriate im...
http://helm.lu/cube/solutions/pocketcube/top/toplayer.html - last update : 2006-01-03
Rubik's Cube: Top Layer (6.7 kb) Relevance : 35.14 % limit to http://helm.lu/, this path : cube/solutions/rubikscube/topedges/
...hat looks like this: The Four Top Edges You will need to find an edge piece that belongs on the top layer. So that you do not undo the hard work you accomplished in putting the top corners in pla... ...otate any of the sides of the cube while looking for these pieces. You are only allowed to spin the bottom layer or the middle layer. We now need to strategically position your foun... ...d piece. Spin either the bottom layer or the middle layer in order to position your found piece to match one of the 5 possible scenarios below. Follow the instructions below each scenario to properly ...
http://helm.lu/cube/solutions/rubikscube/topedges/topedges.html - last update : 2006-01-03
Rubik's Pocket Cube: Finishing The Bottom (3.4 kb) Relevance : 15.71 % limit to http://helm.lu/, this path : cube/solutions/pocketcube/bottomfinish/
...Now that you have: Reviewed the Terminology and Successfully completed the Top Layer and Positioned the Bottom Corners , you are ready to finish the bottom. Rotate the entire cube until you match one ...
http://helm.lu/cube/solutions/pocketcube/bottomfinish/bottomfinish.html - last update : 2006-01-03